Quick Answer: Can I Replace A 10amp Fuse With A 15 Amp Fuse?

Can I replace a 10 amp fuse with a 13 amp fuse?

If you replaced it with 13A fuse, it will allow current more than 10A, so it may possible that other components may get damage due excessive current flow than specified.

If TV components can sustain up to 13 A current, you can replace it..

What would cause my ignition fuse to keep blowing?

If the fuse is now blowing immediately when you turn the ignition key it is a sign of a short in the system. It could have been a loose or frayed wire previously that has just gone completely bad. You’ll need a wiring diagram to begin checking. … A lot of systems operate only when the key is in the “on” position.

How do you stop a fuse from blowing?

To decrease your chances of blowing a fuse, compare the wattage and amperage rating of each of these devices with the amount of power your circuits can handle. This information should be easy to find on their packaging, rating plates or tags.

Is it OK to replace a 3amp fuse with a 5 amp fuse?

If the motor is increased to a 5 amp motor then a 5 amp fuse is ok. You could but you will risk damaging the device it is suppose to protect. Replace with the correct size fuse, if you are having a blown fuse problem you may have a short in the system. … If there is a short either will blow.

Can I replace a 10amp fuse with a 20 amp fuse?

You have replaced the fuse because it most likely blew on a fault. … Get a qualified electrician in to investigate the circuit for the fault and replace the 10 amp fuse with a 10 amp fuse once the problem is corrected. Just because a fuse will fit is not a good reason to put a higher amperage fuse in.

What happens if you use the wrong amp fuse?

Fuses are present to protect the components of the electrical system. Rather than destroying the circuit when there is a surge of power, the fuse blows to protect it. … If you use a fuse with the wrong amperage, the fuse won’t blow as intended, damaging the circuit and resulting in a much larger repair bill.

How much current can a 13 amp fuse take?

BS 1362 Fuse Operation Characteristics In fact a 13A fuse will allow a current of 20A to pass indefinitely without blowing.

Can I replace a 15 amp fuse with a 20 amp fuse?

The answer: It’s possible, but not advisable without an electrician evaluating the situation. You should never just upgrade from a 15-amp breaker to a 20-amp one just because the current one is tripping. Otherwise, you may burn your house down via electrical fire.

Why does my 15a fuse keep blowing?

The fuse is the incorrect amperage rating Check what devices or lights are on that circuit, as it may be the case that a new amplifier pulls too much power, causing the fuse to blow. The more devices there are on one circuit, the heavier the amp load.

What will cause a fuse to keep blowing?

What Happens When a Fuse Blows. There are two conditions that can cause a fuse to blow. First, and most commonly, when too many lights or plug-in appliances draw power from the circuit, it can overload the capacity of the fuse and cause the metal ribbon inside the fuse to melt through.

What happens if you use too big of a fuse?

When oversized fuses are installed, excessive amperage will occur in the event of a circuit fault such as a short to ground. This will cause overheating of the circuit and melting of insulation. In layman’s terms , if a fuse keeps blowing, don’t install a larger one.

What is a 13 amp fuse used for?

Plugs for appliances rated between about 700 watts and 3000 watts (the maximum rating of a wall socket) should be fitted with a 13-amp fuse (coloured brown). For example: 13A Fuse – Washing machine, dishwasher, microwave, kettle, toaster, iron.

Can you replace a fuse with a higher amp?

Never replace a blown fuse with a higher-amp fuse. Always replace the fuse with one with the specified amp rating. You may install the next-smaller-rated fuse to get you by in a pinch until you can purchase a replacement.

Why does my wiper fuse keep blowing?

Faulty wiring or defective wiper motors can cause excessive current flow, resulting in a blown fuse. Defective switches may cause short circuits. Wipers frozen under ice can cause a blown fuse by impeding wiper movement. … In many cases a blown motor circuit fuse may indicate a shorted motor.

How do you fix a fuse that keeps tripping?

The simple answer is to unplug some of them and move the tripped fuse switch in your fuse box back to the ‘on’ position. While we’re on the topic of overloaded circuits, it’s worth mentioning that extension leads are often the source of the problem.

Can I replace a 5a fuse with a 10a fuse?

Possibly yes. What ever is wired into that 5 amp slot is rated for a max of 5 amps, overdrawing more than 5 amps by removing the 5 amp fuse and putting in a 10 amp fuse can possibly short out a circuit.

Can I use a 30 amp fuse instead of 15?

You MAY be ok with a 30amp in place of the normal 15, but you MAY also burn up some wireing, and/or the whole bike. In any case the work done needs a good going over.

How can you tell if a 13a fuse is blown?

Look at the fuse wire. If there is a visible gap in the wire or a dark or metallic smear inside the glass then the fuse is blown and needs to be replaced.

Why does my 15 amp fuse keep blowing?

If the cigarette lighter fuse is 15 amps, then a draw of more than 15 amps will cause it to blow. … And if the problem in your circuit is actually some type of short, putting in a larger fuse may cause the wiring to heat up to the point where it could melt or even cause a fire.