- What does an SWR reading of 1 1 mean?
- What does S RF mean on CB?
- Does SWR affect reception?
- What does an SWR reading of 4 1 indicate?
- Why does my SWR go up when I talk?
- How do I know if my CB antenna is bad?
- What SWR is too high?
- How do I increase the range on my CB radio?
- What is acceptable SWR?
- Is higher or lower antenna gain better?
- Can SWR be too low?
- Why is my SWR so high?
- Can high SWR damage a radio?
- What affects SWR?
- Is 1.5 SWR good?
- Does coax length affect SWR?
What does an SWR reading of 1 1 mean?
What does an SWR reading of 1:1 mean.
The best impedance match has been attained.
An antenna for another frequency band is probably connected.
No power is going to the antenna..
What does S RF mean on CB?
Many CB radios have a built-in meter for testing your antenna system. This testing process revolves around something called “S.W.R.” or Standing Wave Ratio.
Does SWR affect reception?
Simplified answer: There is no relationship between SWR and receive performance. … SWR is a measure of the impedance mismatch between your antenna and transceiver. Whether transmitting or receiving, a higher SWR correlates with a less efficient coupling of energy between the transceiver and antenna.
What does an SWR reading of 4 1 indicate?
What does an SWR reading of 4:1 indicate? Loss of -4 dB. Good impedance match. Gain of +4 dB. Impedance mismatch.
Why does my SWR go up when I talk?
One of the most common causes of high SWR readings is incorrectly connecting your SWR meter to your radio and antenna. When attached incorrectly, readings will be reported as being extremely high even if everything is installed perfectly.
How do I know if my CB antenna is bad?
Testing for a Defective CB AntennaUsing your multimeter, touch one of the probes to the metallic end of the antenna. For fiberglass antennas, this will usually be the tunable tip on the antenna’s end. … Touch the other probe to the metallic threads at the end of the antenna. … As you maintain contact with both probes, measure the circuit’s resistance.
What SWR is too high?
For instance a SWR too high (over 3:1) all over the band can be an indication of a bad part or junction, poor ground or poor location. An SWR too low over the whole band (1:1 for all 40 channels) can indicate a low efficiency antenna or lossy component.
How do I increase the range on my CB radio?
There are several procedures for ensuring maximum output.TUNE THE RADIO. A CB radio is only as good as the coax and antenna connected to it. … USE CB-SPECIFIC ANTENNAS. … ESTABLISH A GROUND PLANE. … CHECK THE VSWR. … ELIMINATE RESISTANCE.
What is acceptable SWR?
What is a good SWR reading ? The best reading possible is 1.01:1 (46dB return loss), but usually a reading below 1.5:1 is acceptable. Outside the perfect world a 1.2:1 (20.8dB return loss) is spot on in most cases. To ensure an accurate reading, it is best to connect the meter at the base of the antenna.
Is higher or lower antenna gain better?
The higher the dBi number of the antenna, the higher the gain, but less of a broad field pattern, meaning that the signal strength will go further but in a narrower direction, as illustrated in the diagram below.
Can SWR be too low?
An SWR too low over the whole band (1:1 for all 40 channels) can indicate a low efficiency antenna or lossy component. … If you have an antenna that’s say, three feet or less, and the SWR tunes great (less than 1.5) across all the channels than maybe your antennas feedline coax or the antenna coil is “lossy”.
Why is my SWR so high?
The most common cause of a high SWR is an antenna shorted to ground. There are two places a short can occur in a CB antenna system, in the coax and in the antenna stud.
Can high SWR damage a radio?
High SWR can reflect enough power back into the radio to create enough heat to cook the final RF transistor. It isn’t usually an immediate failure, it takes some time for that heat to build up and do damage.
What affects SWR?
There are many things other than the antenna that can cause high SWR. SWR meter readings take into consideration the antenna, the coaxial cable, the mount, the mounting location, the vehicle and objects in the antennas near-field environment.
Is 1.5 SWR good?
SWR RANGE EXPLANATIONS. SWR 1.0-1.5: The ideal range! If your SWR is under 1.5, you’re in great shape. If you’re at 1.5 and really, really want to drop down to closer to 1 it’s likely possible to do with addition tuning, different equipment or a different mounting location.
Does coax length affect SWR?
“the length of the feedline will not change the swr it will change the apparent reading depending on what wave length you read the swr at. . just as adding a signifigant length of coax, the resultant loss will look like a lower swr.”